Please Register or
Login
Cart (0) | Total CAD$0.00
Note:

A. The correct size clamp must be used.
B. Bolts in ground joints are designed to bend as they are tightened. This allows the clamp to conform to the hose outside diameter.
C. Always tighten bolts to their specified torque value. 

Hose ID Hose OD Dixon Plated Iron Part # Dixon Stainless Steel Part # Torque Dixon Brass Part # Torque
From To
1/4" 36/64" 42/64" BD 4 --- 6 --- --
3/8" 44/64" 56/64" CD 4 --- 6 --- --
1/2" 52/64" 60/64" DD 4 --- 6 --- --
1/2" 60/64" 1-4/64" B4 4 RB4 12 BB4 10
1/2" 1-4/64" 1-12/64" B5 4 --- 12 --- --
3/4" 1-10/64" 1-20/64" BU9 4 RBU9 21 BBU9 18
3/4" 1-20/64" 1-32/64" B9 RB9 21 BB9 18
3/4" 1-32/64" 1-44/64" B10 4 --- 21 BB10 --
1/2" 58/64" 1-2/64" 968 1 --- 6 --- --
1" 1-26/64" 1-36/64" 156 1, 4 --- 21 --- --
1" 1-34/64" 1-46/64" BU14 RBU14 21 BBU14 18
1" 1-44/64" 1-60/64" B14 4 RB14 21 BB14 18
1" 1-60/64" 2-8/64" B15 --- 21 --- --
1-1/4" 1-32/64" 1-50/64" BU18 --- 40 --- --
1-1/4" 1-44/64" 1-56/64" 187 1 --- 21 --- --
1-1/4" 1-50/64" 2-6/64" BU19 --- 40 --- --
1-1/4" 1-56/64" 2-4/64" 206 1 --- 21 --- --
1-1/4" 2-8/64" 2-24/64" B19 RB19 40 BB19 2 28
1-1/2" 1-52/64" 2" BU22 --- 40 --- --
1-1/2" 2" 2-14/64" B22 --- 40 --- --
1-1/2" 2" 2-8/64" 212 1 --- 21 --- --
1-1/2" 2-4/64" 2-16/64" 225 1 --- 40 --- --
1-1/2" 2-12/64" 2-24/64" BU24 RBU24 40 BBU24 2 28
1-1/2" 2-24/64" 2-36/64" B24 RB24 40 --- --
1-1/2" 2-36/64" 2-48/64" B25 --- 40 --- --
2" 2-16/64" 2-32/64" 250 1, 5 --- 40 --- --
2" 2-22/64" 2-34/64" BU28 --- 60 --- --
2" 2-32/64" 2-48/64" 275 1, 5 --- 40 --- --
2" 2-32/64" 2-50/64" BU29 RBU29 60 BBU29 2 40
2" 2-48/64" 3-4/64" B29 RB29 60 BB29 2 40
2" 2-48/64" 3-4/64" 306 1, 5 --- 60 --- --
2" 3-6/64" 3-28/64" B30 --- 60 --- --
2-1/2" 3-4/64" 3-32/64" 350 1 --- 60 --- --
2-1/2" 3-6/64" 3-28/64" BU34 --- 60 --- --
2-1/2" 3-32/64" 3-60/64" B34 --- 150 --- --
3" 3-32/64" 3-48/64" 375 1 --- 60 --- --
3" 3-32/64" 3-60/64" BU35 RBU35 150 --- --
3" 3-48/64" 4" 401 1 --- 150 --- --
3" 3-52/64" 4-4/64" B35 --- 150 --- --
3" 4" 4-12/64" 418 1 --- 200 --- --
3" 4-4/64" 4-28/64" B39 --- 200 --- --
3" 4-12/64" 4-32/64" 450 1 --- 200 --- --
3" 4-16/64" 4-52/64" BS39 150
4" 4-40/64" 5" B45 150
4" 4-56/64" 5-16/64" BS49 200
4" 5-16/64" 5-38/64" BU49 200
4" 5-34/64" 5-60/64" B49 200
6" 6-56/64" 7-24/64" 750 200
6" 7-32/64" 8" 850 200
1 4 gripping fingers
2 will become obsolete as inventory is depleted
3 torque applies to plated iron and stainless steel clamps
4 investment cast carbon steel
5 not to be used with Dixon GF81, GB26, WF81, B26, RGF81, RGB26, BGF81, BGB26, RWF81, RB26

D. Periodic re-tightening of bolts is required due to "cold flow" phenomenon present in all rubber hoses.
E. Boss Clamps are for single use only! Once removed they are to be discarded.

2 Bolt Clamp Bolt Tightening Sequence

Using a torque wrench, begin tightening the bolts as follows:
a) First bolt (nut facing assembler) 1 full turn.
b) Second bolt (opposite first bolt) 1 full turn.
c) Repeat procedure "a" and "b" until both bolts have reached the recommended torque.
d) Remove assembly from vise.

4 Bolt Clamp Bolt Tightening Sequence

Using a torque wrench, begin tightening the bolts as follows:
a) Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) 1 full turn.
b) Front bolt (bolt with nut facing assembler that is closest to gripping finger) 1 full turn.
c) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
d) Opposite side back bolt (bolt with nut facing assembler furthest away from gripping finger) 1 full turn.
e) Opposite side front bolt (bolt with nut facing assembler closest to gripping finger) 1 full turn.
f) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
g) Repeat above procedure "a" through "f" until all of the bolts have reached the recommended torque.
h) Remove assembly from vise.

6 Bolt Clamp Bolt Tightening Sequence

Using a torque wrench, begin tightening the bolts as follows:
a) Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) having "X" near it one full turn.
b) Front bolt (bolt with nut facing assembler that is closest to gripping finger) of same segment one full turn.
c) Moving to clamp segment to the left of the one just tightened, snug bolts by hand (if bolts are loose).
d) Back bolt to one full turn.
e) Front bolt one full turn.
f) Moving to clamp segment to the left of the one just tightened, snug bolts by hand (if bolts are loose).
g) Back bolt one full turn.
h) Front bolt one full turn.
i) Repeat above procedure "a" through "h" until all of the bolts have reached the recommended torque.
j) Remove assembly from vise.


Use Chrome for faster page loading!